Skoda Fabia

Since 2000 of release



Shkoda Fabija
# 1.1. The car description
# 2. The engine
# 3. Greasing system
# 4. The power supply system
# 5. Cooling system
# 6. System of release of the fulfilled gases
- 7. Transmission and a running gear
   - 7.1. A transmission
      7.1.1. Technical characteristics of transmissions (КП)
      - 7.1.2. Type 002 transmission
         7.1.2.1. Removal and installation
         7.1.2.2. Check of level and oil pouring in a transmission
         7.1.2.3. Refuelling of a new box
         7.1.2.4. Replacement of a cover of the lever of a gear change
         7.1.2.5. Removal and installation of a drive of a gear change
         7.1.2.6. Dismantling and assemblage of the mechanism of a gear change
         7.1.2.7. Check of correctness of adjustment of a drive of a gear change
         7.1.2.8. Adjustment of a drive of a gear change
      # 7.1.3. A type transmission 02T
   # 7.2. A forward suspension bracket
   # 7.3. A back suspension bracket
# 8. A steering
# 9. Brake system
# 10. An electric equipment
# 11. A body
# 12. Electroschemes




7.1.2.6. Dismantling and assemblage of the mechanism of a gear change
THE GENERAL DATA

Fastening of cables of a drive of a transmission

1 – a cable of inclusion of transfers;
2 – a cable of a choice of transfers;
3 – a lock ring of a tip of a cable;
4 – a lock ring;
5 – the mechanism case;
6 – an arm of cables of a drive;
7 – a pillow;
8 – распорные plugs;
9 – a bolt of fastening of an arm;
10 – a cable tip;
11 – a lock ring of an axis;
12 – the axis plug;
13 – the lever of a choice of transfers;
14 – a lever axis;
15 – ползун;
16 – the gear change lever;
17 – a nut

PERFORMANCE ORDER
1. Remove a drive of a gear change from the car (subsection 7.1.2.5 see).
2. Pull upwards the lever of 3 gear changes, simultaneously pressing the plug 4 against the stop downwards (overcoming resistance of a spring 1), and remove from the lever the released lock ring 2.
3. Remove from the lever 12 (fig. of the Detail of the mechanism of a gear change see) a spring 3 with plugs 2 and 4.
4. Unbend fixing pads and uncover 22 mechanisms of a gear change.
5. Remove lock rings 4 (fig. Fastening of cables of a drive of a transmission see), крепящие cables 1 and 2 to the case 5 mechanisms.
6. Remove lock rings 25 (fig. of the Detail of the mechanism of a gear change see) and disconnect cables 23 and 24 drives from the intermediate lever of inclusion of transfers executed for a single whole about directing 9 levers of a gear change and the intermediate lever of 20 choice of transfers.
7. Turn away a bolt of 21 fastenings and remove the intermediate lever 20 choice of transfers from an axis 17 and a spherical finger directing 9 levers of a gear change.
8. Remove a lock ring of 28 axes of the intermediate lever of a choice of transfers.
9. Remove the ends of a returnable spring 19 from a spherical finger directing 9 levers of a gear change.
10. Take out an axis 17 with a spring 19 of an aperture of the case of the mechanism.
11. Take out plugs of 15 and 27 axes.
12. Remove from an axis directing plug 18 with a spring 19.
13. Remove from the directing plug 18 spring 19.
14. Turn away two bolts of 5 fastenings and uncover 6 hinges.
15. Having compressed a holder 7 hinges, take out it together with the lever of 12 gear changes from the case 14 mechanisms.
16. Remove directing 9 from the lever of 12 gear changes.
17. Remove шумоизоляционную a washer 10 from the lever of 12 gear changes.
18. Dissolve a holder 7 hinges and remove it from a spherical surface directing 9.
19. Take out from a holder 7 loose leaf 8 hinges.
20. Remove the rubber buffer 13.
21. Replace the damaged or worn out details.
22. Collect and establish into place the gear change mechanism in an order, the return to dismantling. Thus establish a returnable spring 1, as is shown in drawing. After installation adjust a gear change drive (2 – the rubber buffer; 3 – a spherical finger directing the gear change lever).