Skoda Fabia

Since 2000 of release



Shkoda Fabija
# 1.1. The car description
# 2. The engine
# 3. Greasing system
# 4. The power supply system
# 5. Cooling system
# 6. System of release of the fulfilled gases
- 7. Transmission and a running gear
   # 7.1. A transmission
   - 7.2. A forward suspension bracket
      7.2.1. Removal and installation of a telescopic rack
      7.2.2. Repair of a telescopic rack
      7.2.3. Replacement of a spherical support
      7.2.4. Removal and installation of the lever of a forward suspension bracket
      7.2.5. Removal and installation of an arm of a forward suspension bracket
      7.2.6. Replacement резинометаллической support
      7.2.7. Removal and installation of the stabilizer of cross-section stability
   # 7.3. A back suspension bracket
# 8. A steering
# 9. Brake system
# 10. An electric equipment
# 11. A body
# 12. Electroschemes




7.2. A forward suspension bracket

7.2.1. Removal and installation of a telescopic rack
THE GENERAL DATA

Fastening of a spherical support

1 – the lever of a forward suspension bracket;

2 – a bolt;

3 – a spherical support

Details of a rack of a forward suspension bracket

1 – a rotary fist;
2 – a nut;
3 – a coupling bolt;
4 – амортизаторная a rack;
5 – the compression buffer;
6 – a protective casing;
7 – a spring of a forward suspension bracket;
8 – the persistent bearing of a support;
9 – a rack support;
10 – a rod nut;
11 – a support plate;
12 – a bolt of fastening of a rack;
13 – a protective cap

Details of a beam of a forward suspension bracket

1 – a beam;
2 – a nut of fastening of a rack to a stabilizer bar;
3 – a stabilizer bar;
4 – a bar pillow;
5 – a pillow holder;
6 – a nut of fastening of a rack of the stabilizer to a telescopic rack;
7 – a rack of the stabilizer of cross-section stability;
8 – an arm;
9, 10, 19, 22 – bolts;
11 – резинометаллическая a support;
12 – the lever of a forward suspension bracket;
13 – a lock plate;
14 – a nut of a finger of a spherical support;
15 – a spherical support;
16 – a bolt of fastening of a spherical support;
17 – an air line;
18 – percussion caps;
20 – a beam arm;
21 – a bolt of fastening of the steering mechanism;
23 – bolts of fastening of a back support of the power unit to a transmission;
24 – a bolt of fastening of a back support of the power unit to a beam;
25 – a back support of the power unit

PERFORMANCE ORDER
1. Ослабьте an inhaling of bolts 9 (fig. of the Detail of a forward suspension bracket see) fastenings of a corresponding wheel and a nut of 10 naves.
2. Raise and establish on reliable support a forward part of the car.
3. Remove a forward wheel, definitively having turned away bolts of its fastening.
4. Turn away a nut of 26 fastenings and disconnect a rack 27 stabilizers of cross-section stability from a telescopic rack 1.
5. Disconnect wires from the gauge of 24 frequencies of rotation of a wheel. Turn away a bolt of 25 fastenings and remove the gauge of 24 frequencies of rotation of a wheel.
6. Remove a support 13 and suspend it on a wire to a body (subsection 9.5.1 see) or (subsection 9.6.1 see).
7. Mark position of bolts 2 (fig. Fastening of a spherical support see) fastenings of the spherical hinge on the lever of 1 suspension bracket, having led round contours of heads of bolts. It will help to keep approximately after assemblage corners of installation of wheels.
8. Turn away bolts of 2 fastenings of a spherical support 3 to the lever.
9. By means of a special stripper 1 (fig. of Vypressovka шлицевого a tip of an external SHRUS from a nave see) выпрессуйте шлицевый a tip of an external SHRUS from a nave of 2 wheels. In the absence of a stripper it can be made hammer blows through the wooden prorate on an end face шлицевого a tip.
10. Suspend a wheel drive to a body by means of a wire.
11. Disconnect steering draught from a rotary fist (subsection 8.4.1 see) and suspend it on a wire to a body.
12. In подкапотном space turn away three bolts 12 (fig. of the Detail of a rack of a forward suspension bracket) rack fastenings to a body see and remove a rack through a wheel niche.
13. Establish a telescopic rack upside-down, having replaced nuts of a nave and a spherical finger of a tip of steering draught, and also bolts 16 (fig. of the Detail of a beam of a forward suspension bracket see) fastenings of a spherical support and their lock plate 13. First of all roll bolts 12 (fig. of the Detail of a rack of a forward suspension bracket see) rack fastenings from outside a motor compartment.

The inhaling moments, Нм

Nut of a nave of a wheel
30
Bolts of fastening of the spherical hinge to the suspension bracket lever
20, then to tighten on 90
Nut of a spherical finger of a tip of steering draught
20, then to tighten on 90
Nut of fastening of a rack of the stabilizer of cross-section stability to a forward rack
40
Bolts of the top fastening of a forward rack
25
Bolt of fastening of the gauge of frequency of rotation of a wheel
8
Bolts of fastening of a wheel
120