Skoda Fabia

Since 2000 of release



Shkoda Fabija
# 1.1. The car description
# 2. The engine
- 3. Greasing system
   3.1. Removal and installation oil картера the engine
   3.2. Repair of the oil pump on engines of 1,0 l, 37 kw and 1,4 l, 50 kw
   3.3. Replacement of the oil pump
   3.4. The oil filter of the diesel engine
   3.5. Check of level of oil in картере the engine
   3.6. Replacement of oil and the oil filter
# 4. The power supply system
# 5. Cooling system
# 6. System of release of the fulfilled gases
# 7. Transmission and a running gear
# 8. A steering
# 9. Brake system
# 10. An electric equipment
# 11. A body
# 12. Electroschemes



3.1. Removal and installation oil картера the engine

PETROL ENGINES

PERFORMANCE ORDER
1. Remove грязезащитный an engine guard.
2. Merge oil from картера the engine.
3. On engines of 1,0 l, 37 kw and 1,4 l, 50 kw disconnect a pipe of system of cooling from arms under oil картером.
4. Turn away bolts of fastening oil картера. On engines of 1,4 l, 50 kw also turn away bolts 14 (fig. of the Detail of system of greasing of the engine of 1,0 l, 37 kw and 1,4 l, 50 kw) fastenings of a support 10 with the bottom guard 9 to картеру couplings see and remove a support.
5. Remove oil картер from the block of cylinders. On engines of 1,0 l, 37 kw and 1,4 l, 50 kw thus wring out a pipe of system of cooling. On engines of 1,0 l, 37 kw remove a lining oil картера.
6. Carefully clear of the rests of oil and old hermetic interfaced surfaces oil картера and the block of cylinders.
7. On engines of 1,0 l, 37 kw establish a new lining картера and put hermetic in the field of connection of a cover of distributive gear wheels with the block of cylinders.
8. On other engines put a layer of hermetic in the thickness of 2-3 mm on a flange oil картера, as is shown in drawing. Watch, that the layer of hermetic did not exceed 3 mm, differently superfluous mastic will be squeezed out in oil картера that will lead to a contamination маслоприемника. On a flange part from outside a flywheel be especially cautious. In a place specified by an arrow And, put большее quantity of hermetic according to the sizes specified in drawing.
9. Establish the bottom guard картера couplings on a support.
10. Establish oil картер into place, if necessary wringing out a pipe of system of cooling. Work should be spent with the assistant.
11. Acquire bolts of fastening oil картера to the block of cylinders in the sequence specified in drawing. Then screw, without tightening, two bolts of fastening of a support with the bottom guard to картеру couplings.
12. Tighten bolts of fastening oil картера to the block of cylinders in the sequence specified in drawing, and definitively tighten two bolts of fastening of a support with the bottom guard to картеру couplings.
13. Definitively tighten bolts of fastening oil картера to the block of cylinders in the specified sequence.
14. Fix a pipe of system of cooling.
15. Allow to dry up to condensing mastic during 30 mines and only after that fill in oil in картер the engine.

The inhaling moments, Нм

Bolts of fastening of a support to картеру couplings
45
Bolts of fastening oil картера to the block of cylinders:
  – М6
10
  – М8
20

DIESEL ENGINES

PERFORMANCE ORDER
1. Remove грязезащитный an engine guard.
2. Merge oil from картера the engine.
3. Turn away bolts of fastening oil картера.
4. Remove oil картер from the block of cylinders.
5. Carefully clear of the rests of oil and old hermetic interfaced surfaces oil картера and the block of cylinders.
6. Put a layer of hermetic in the thickness of 2-3 mm on a flange oil картера as it is specified by arrows in drawing. Watch, that the layer of hermetic did not exceed 3 mm, differently superfluous mastic will be squeezed out in oil картера that will lead to a contamination маслоприемника. On a flange part from outside a flywheel be especially cautious.
7. Establish oil картер into place.
8. Acquire bolts of fastening oil картера to the block of cylinders cross-wise. Then turn, without tightening, three bolts of fastening oil картера to картеру couplings.
9. Tighten bolts of fastening oil картера to the block of cylinders cross-wise and definitively tighten three bolts of fastening oil картера to картеру couplings.
10. Definitively tighten bolts of fastening oil картера to the block of cylinders cross-wise.
11. Allow to dry up to condensing mastic during 30 mines and only after that fill in oil in картер the engine.

The inhaling moments, Нм

Bolts of fastening oil картера to картеру couplings
45
Bolts of fastening oil картера to the block of cylinders
15