Skoda Fabia

Since 2000 of release



Shkoda Fabija
# 1.1. The car description
# 2. The engine
# 3. Greasing system
# 4. The power supply system
# 5. Cooling system
# 6. System of release of the fulfilled gases
# 7. Transmission and a running gear
# 8. A steering
- 9. Brake system
   # 9.1. Pedal knot
   9.2. The vacuum amplifier
   9.3. The main brake cylinder
   9.4. A pressure regulator (on models without ABS)
   # 9.5. The brake mechanism of a forward wheel of type FS III
   # 9.6. The brake mechanism of a forward wheel of type FS II
   # 9.7. The brake mechanism of a back wheel (drum-type)
   - 9.8. The brake mechanism of a back wheel (disk)
      9.8.1. Replacement brake колодок
      9.8.2. Replacement of a brake disk
      9.8.3. Support repair
   # 9.9. A lay brake
   # 9.10. Antiblocking system (ABS)
# 10. An electric equipment
# 11. A body
# 12. Electroschemes




9.8.3. Support repair
THE GENERAL DATA

Details of a support of the brake disk mechanism of a back wheel
1 – a bolt of fastening of a support;
2 – a protective cap;
3 – the valve of release of air;
4 – a directing finger;
5 – a protective cover;
6 – directing колодок;
7 – a protective cap;
8 – the piston;
9 – a sealing ring;
10 – a support

Removal of a sealing ring from the support cylinder

1 – a shovel;

2 – a sealing ring;

3 – the support cylinder

Installation of a protective cap on the piston

1 – a protective cap;

2 – the piston

Piston installation in the support cylinder

1 – the support cylinder;

2 – a protective cap;

3 – the piston

The prevention

At support repair always completely use the repair complete set.


PERFORMANCE ORDER
1. Remove a wheel, preliminary having weakened bolts of its fastening on the car standing on the earth.
2. Turn away a hollow bolt of fastening of a brake hose 15 (fig. of the Detail of the brake disk mechanism of a back wheel see) to a support 17. Having disconnected a brake hose, muffle its aperture.
3. Turn away two bolts 2 (fig. the Detachment of a cable of a drive of a lay brake see) support fastenings, holding with the second key directing fingers 3 for шестигранники.
4. Remove a support 17 (fig. of the Detail of the brake disk mechanism of a back wheel see) with directing 21 колодок.
5. Take out from a support 17 brake колодки 18 and 19. If колодки it is not necessary to replace, mark them then to establish on former places. While in service колодки are earned extra if to change, therefore, their places, braking will be non-uniform.
6. Turn out from the cylinder the piston 8 (fig. of the Detail of a support of the brake disk mechanism of a back wheel) by means of the special adaptation see or at its absence to use, for example, nippers for removal of lock rings. On the piston there are for this purpose special dredging.
7. Remove a protective cap 7 from the cylinder. The cap torn, cracked or lost elasticity replace.
8. Take out a sealing ring 2 (fig. Removal of a sealing ring from the support cylinder see) of проточки the cylinder by means of a wooden or plastic shovel 1 not to damage a mirror of the cylinder 3.
9. Examine a mirror of the cylinder and the piston. In the presence of deep рисок, scratches, roughnesses, etc. replace a support in gathering.
10. Carefully wash out spirit and dry a stream of compressed air the piston and the cylinder.
11. Replace the protective covers torn or lost elasticity 5 (fig. of the Detail of a support of the brake disk mechanism of a back wheel see) directing fingers.
12. Grease the piston 8 and a new sealing ring with 9 greasing G 052 150 A2 or a brake liquid. A sealing ring replace at each dismantling, irrespective of its condition.
13. Establish a new sealing ring 9 in проточку the cylinder. A ring replace at each dismantling, irrespective of its condition.
14. Put on a protective cap 1 (fig. Installation of a protective cap on the piston see) a back part of the piston 2, having turned its internal edge inside out.
15. Accurately insert an external edge of a protective cap 2 (fig. piston Installation in the support cylinder see) into a groove of the cylinder 1.
16. Screw the piston by means of the special adaptation in the cylinder, and at its absence it is possible to take advantage, for example, of nippers for removal of lock rings. On the piston there are for this purpose special dredging.
17. Clear of a dirt and old greasing directing fingers 4 (fig. of the Detail of a support of the brake disk mechanism of a back wheel see) and apertures under them in directing 6 колодок. Check up: fingers should freely, without jammings to move in apertures directing.
18. Establish protective covers 5 on fingers, having put on a cover edge a finger fillet. Before installation grease fingers under covers консистентной greasing (greasing is included into the repair complete set). Establish fingers in apertures directing колодок, having put on edges of covers fillets directing колодок.
19. Establish a support upside-down, having placed in it колодки according to earlier made marks. At connection of a brake hose 15 (fig. of the Detail of the brake disk mechanism of a back wheel see) pay attention – under a hose tip the metal lining should be established.
20. Pump over brake system (subsection 9.9.6 see) and adjust a lay brake (subsection 9.9.2 see).