Skoda Fabia

Since 2000 of release



Shkoda Fabija
# 1.1. The car description
# 2. The engine
# 3. Greasing system
- 4. The power supply system
   4.1. Removal and installation of the air filter
   4.2. Replacement of a filtering element of the air filter
   4.3. Replacement of the gauge of the index of level of fuel
   4.4. Removal and installation of a fuel tank
   4.5. Check of the air valve
   4.6. Check of the gravitational valve
   4.7. Replacement of the fuel filter
   4.8. Check of the valve of heating of fuel
   4.9. Replacement of an adsorber of system of catching of steams of fuel
   4.10. Replacement of a fuel radiator
   4.11. Removal and installation of the vacuum pump of the diesel engine
   4.12. Removal and installation of an inlet pipe of the engine
   4.13. Removal and installation of a pedal of an accelerator
   # 4.14. Removal and installation of atomizers
   4.15. Check of a feed circuit of atomizers of the petrol engine
   4.16. Check of resistance of a pump-atomizer
   4.17. Check of candles накаливания the diesel engine of 1,9 l, 47 kw
   4.18. Check of a feed circuit of candles накаливания
   4.19. Check of the gauge of temperature of a cooling liquid
   4.20. Check of the gauge of temperature of air arriving in the engine
   4.21. Check of the gauge of temperature of fuel of the diesel engine of 1,9 l, 74 kw
   4.22. Check of the gauge of frequency of rotation of a cranked shaft
   4.23. Check of a drive throttle заслонки
   4.24. Check of the gauge of position of a camshaft
   4.25. Check элекромагнитного the valve рециркуляции the fulfilled gases
   4.26. Check of the relay of the fuel pump of engines of 1,4 l, 55 and 74 kw
   4.27. Check of the electromagnetic valve of a purge of an adsorber
   4.28. Removal and installation турбокомпрессора
   4.29. Removal and installation of an intermediate cooler of air
   4.30. Check of the valve of pressure of pressurisation
# 5. Cooling system
# 6. System of release of the fulfilled gases
# 7. Transmission and a running gear
# 8. A steering
# 9. Brake system
# 10. An electric equipment
# 11. A body
# 12. Electroschemes




4.28. Removal and installation турбокомпрессора
THE GENERAL DATA

Турбокомпрессор with a final collector

1 – a final collector;
2 – an inlet pipe of the engine;
3 – the case throttle заслонки;
4 – a lining of an inlet pipe;
5 – a bolt of fastening of an inlet pipe;
6 – a collector lining;
7 – a washer;
8 – a nut;
9 – a branch pipe of an air line of the air filter;
10 – a branch pipe of an air line of an intermediate cooler;
11 – the tank of a regulator of pressure of pressurisation;
12 – теплоизоляционный the screen;

13 – an arm турбокомпрессора;
14 – a bolt of fastening of an arm;
15 – a fastening bolt турбокомпрессора;
16 – a sealing ring;
17 – the union of a tube oil plum;
18 – a bolt of fastening of a tube oil plum;
19 – a tube plum of oil from турбокомпрессора;
20 – a tube lining;
21 – турбокомпрессор;
22 – a lining of a reception pipe;
23 – a reception pipe of the muffler;
24 – the union of a tube of a supply of oil;
25 – a tube of a supply of oil;
26 – a bolt of fastening of a tube

Турбокомпрессор it is possible to remove and replace only in gathering with a final collector and a regulator of pressure of pressurisation.

Турбокомпрессор to repair is not subject, at failure it is necessary to replace it.

PERFORMANCE ORDER
1. Remove грязезащитный an engine guard.
2. Remove a drive of the right wheel (subsection 7.1.3.7 see).
3. Remove a protective casing of a semiaxis.
4. Disconnect the bottom air line 1 (fig. the Bottom air line of pressurisation see) from an intermediate cooler of air.
5. Disconnect from турбокомпрессора hoses bottom 2 (fig. of Turbokompressor (the bottom view) see) and back 1 air lines.
6. Turn on накидную a nut and disconnect from the block of cylinders a tube 19 (fig. of Turbokompressor with a final collector see) plum of oil from турбокомпрессора.
7. Turn out bolts 14 and 15 and remove an arm 13.
8. Disconnect a vacuum hose 7 (fig. of Turbokompressor (the bottom view) see) from a regulator of pressure of pressurisation.
9. Remove a reception pipe of the muffler (subsection 6.2 and subsection 6.3 see).
10. Remove the top casing of the engine (subsection 2.1 see).
11. Remove the top air line 6 (fig. the Motor compartment see).
12. Remove tubes рециркуляции the fulfilled gases between a final collector and an inlet pipe of the engine.
13. Turn away bolts 18 (fig. of Turbokompressor with a final collector see) and lift the receiver 19.
14. Turn away a nut of 8 fastenings of a final collector.
15. Remove a final collector with турбокомпрессором, having lowered it downwards.
16. Establish a final collector with турбокомпрессором upside-down, having replaced all самоконтрящиеся nuts; fill in engine oil in турбокомпрессор before joining to it tubes 25 supplies of oil.
17. After installation турбокомпрессора start up the engine and allow to it to work idling not less than 1 mines that турбокомпрессор it was filled with oil.